Teile für Wärmemotoren
S08671904200
Funkgesteuerter Verbrennungsmotor MOTORGESTÜTZ O.S. FS120SIII, SE -120AX- FS155- FS200S
Motorgehäuse aus Aluminium für O.S.-Motoren FS-120SIII, FS-120SE, FS-155, FS-200S und 120AX. Original gebohrt und mit Gewinde versehen. Wird mit Schrauben und Unterlegscheiben zur Befestigung geliefert. Abmessungen: A = 53,7mm, B = 56mm, C = 25mm.
57,90 €
Bruttopreis
Funkgesteuerter Verbrennungsmotor MOTORGESTÜTZ O.S. FS120SIII, SE -120AX- FS155- FS200S
Plus de details Nicht auf LagerFunkgesteuerter Verbrennungsmotor MOTORGESTÜTZ O.S. FS120SIII, SE -120AX- FS155- FS200S
57,90 €
Versand innerhalb von 48 Stunden 
343330 produkte auf Lager 
Kundendienst 
Sichere Bezahlung 
Motorgehäuse aus Aluminium für O.S.-Motoren FS-120SIII, FS-120SE, FS-155, FS-200S und 120AX. Original gebohrt und mit Gewinde versehen. Wird mit Schrauben und Unterlegscheiben zur Befestigung geliefert. Abmessungen: A = 53,7mm, B = 56mm, C = 25mm.
- Motorzubehör Typen
- Motorgebäude
- Motoren
- Thermal
- Nutzungsniveau/Schwierigkeitsgrad
- Thermal
- Produkttypen
- Motoren und Variatoren für funkkontrollierte Modelle
- Motorzugriffszugriffe
- Motorgebäude
Produkte, die Ihnen gefallen könnten
150ml bomb RC plane/black boat 71. Sold by unit.
\n
\nRC plane/boat paintings were specially designed for the decoration of RC models.\nThey resist fuel and can be applied to most surfaces. Do not apply to polystyrene or other expanded foam.
\n
\n to get the best result \n
\n Danger mentions: \n
\n Caution: \n
\n
\nRC plane/boat paintings were specially designed for the decoration of RC models.\nThey resist fuel and can be applied to most surfaces. Do not apply to polystyrene or other expanded foam.
\n
\n to get the best result \n
- 1) Always clean the surfaces to be painted and sand them with paper of 1000, in the event of use directly on wood, please use the S138211003 Appret \n
- 2) Hide the areas that you do not want to paint \n
- 3) Etage the paint bomb vigorously for 2 minutes \n
- 4) Spray the paint at a distance of 20 to 30cm above the surface in a thin uniform layer \n
- 5) Wait 24 hours before passing another layer or withdraw the masking adhesives. \n
- 6) At the end of the use, please put your head down down and press the nozzle to the paint stops, this will avoid the plug of the nozzle
\n Danger mentions: \n
- Repeated exposure can cause dryness or skin chapters. \n
- Extremely flammable aerosol. \n
- Pressure container: can break out under the effect of heat. \n
- can cause a skin allergy. \n
- causes severe eye irritation.
\n Caution: \n
- Hold out of heat, hot surfaces, sparks, bare flames and any other source of inflammation. Do not smoke. \n
- Do not puncture or burn, even after use. \n
- Wear protective gloves, protective clothing, eye/face protective equipment. \n
- In case of contact with the eyes: rinse with precaution with water for several minutes. Remove the contact lenses if the victim bears it and if they can be easily removed. Continue to rinse. \n
- In case of irritation or rash: consult a doctor. \n
- Protect solar radiation. Do not expose to a temperature above 50 ° C/122 ° F.